- 1 Can a transducer be mounted on an angle?
- 2 What side of the boat should the transducer be on?
- 3 How deep in the water should a transducer be?
- 4 How deep can a 1kW transducer read?
- 5 How far should a prop be from a transducer?
- 6 Where is the best place to mount a transducer?
- 7 Can you mount a transducer on the port side?
- 8 What happens if your transducer is not level?
- 9 How do I know if my transducer is bad?
- 10 Will a transducer work backwards?
- 11 Does it matter which way your transducer faces?
- 12 Can you have 2 transducers side by side?
- 13 Will a Lowrance transducer work on a Humminbird?
Can a transducer be mounted on an angle?
Both the front-to-rear and side-to-side transducer mounting angles are critical to high-speed performance. Sometimes a transducer mounted parallel with the hull bottom also works fine, but even the slightest nose-down angle can cause turbulence or cavitation that kills performance.
What side of the boat should the transducer be on?
The location should be as close to the center of the boat as possible, but on the side of the downward swing the propeller. On the majority of boats, this will be on the starboard (right) side.
How deep in the water should a transducer be?
Ensure the boat is in water greater than 2′ but less than the depth capability of the unit and the transducer is fully submerged. Remember the sonar signal cannot pass through air.
How deep can a 1kW transducer read?
Simrad now uses 1kW transducers with ceramic elements on some models, which it claims can be used in waters up to 1800 metres deep. Furuno has a wide range of transducers up to 3kW and has recently catered to the small trailer boat angler with the introduction of the FCV-585 and 620 models.
How far should a prop be from a transducer?
Ensure there is adequate distance from the propeller(s). On outboard or inboard/outboard boats, it is best to locate the transducer at least 15″ (38.1 cm) to the side of the propeller (s).
Where is the best place to mount a transducer?
Transducer placement should be aft and close to the centerline. It needs to be located low enough that the transducer is in the water at all times. Consider items such as the lifting strap placement into the location as well as trailer bunks and rollers if it is a trailered vessel.
Can you mount a transducer on the port side?
DETERMINE THE TRANSDUCER MOUNTING ANGLE The general rule of thumb is to mount the transducer to the starboard side, which is the down stroke of most single outboard boat propellers (right hand lower unit). The slightest bit of downward angle can cause the transducer to nose-down causing turbulence and poor performance.
What happens if your transducer is not level?
In 2D sonar If you can see some sort of arch and all the arches are tilted forward or backwards then the transducer is not level (there’s an example in the video). In side imaging drive by something long and straight. If the transducer is not leveled the image will be distorted.
How do I know if my transducer is bad?
Here are the most common types of incorrect display readings that are caused by transducer errors:
- Display shows surface reading, but no bottom reading.
- Display shows wrong depth reading.
- Display shows erratic readings (especially when the boat speeds up)
Will a transducer work backwards?
The transducers are calibrated and made to mount on the transom with a left and right but when mounting them on the bow of the boat left and right are reversed. If you mount the transducer as shown in Brian’s photo above, it should be oriented correctly.
Does it matter which way your transducer faces?
So the short answer is that no, it doesn’t matter which way you face the “front” of your transducer.. the read out is going to look just the same to you. You do, however, want the BOTTOM of your transducer to face as straight down as you can, within reason.
Can you have 2 transducers side by side?
While it is not recommended that more than one transducer be run simultaneously, there can be multiple transducers installed on a boat. For best results, two transducers need to have at least a 50 kHz difference in their frequencies to not cause interference.
Will a Lowrance transducer work on a Humminbird?
The Lowrance transducer will function like a Humminbird transducer.