- 1 Can you replace a piston rod?
- 2 Can you change pistons and rods without removing the engine?
- 3 Can a piston be replaced?
- 4 How much does it cost to replace a cylinder on a boat motor?
- 5 How much does it cost to replace pistons?
- 6 Can a damaged piston be repaired?
- 7 Do Pistons go bad?
- 8 Can I change crankshaft without removing the engine?
- 9 How do I know if I need new pistons?
- 10 What burns a hole in a piston?
- 11 What does a bad piston sound like?
- 12 How much does it cost to fix a piston slap?
- 13 How many hours do boat motors last?
- 14 How much fuel does a 70 hp outboard use?
- 15 Are boat motors hard to work on?
Can you replace a piston rod?
Yes, you can replace one piston, but if you don’t pull the engine down and have it balanced to the rest of the rotating assembly, it technically could be out of balance. If you buy the exact same piston you probably won’t notice it.
Can you change pistons and rods without removing the engine?
In answer to your question, yes, it can be done, make sure, the crank is turned in the right position so the rods align to it, and get a ring compressor, it would make the work easier.
Can a piston be replaced?
Any pistons that are worn or damaged must be replaced. In most cases, if one piston is bad, the others are too so, all should be replaced as a complete set. Many pistons that appear to be in good condition and show no signs of scuffing may still have to be replaced because the upper ring lands are worn.
How much does it cost to replace a cylinder on a boat motor?
Unfortunately, replacing an engine often costs more than the vehicle’s worth. On average, you’re looking at $4,000 to $5,000 dollars to replace a 4 cylinder engine.
How much does it cost to replace pistons?
The average auto mechanic charges between $100 to $200 per hour to replace a blown piston. A new piston ring costs around $100, so you’ll have to add that to the cost of how long it takes your mechanic to complete the job.
Can a damaged piston be repaired?
In this case you are probably not going to cut it with replacing broken parts, your engine needs to be overhauled. The faulty piston must be replaced but the cilinder walls are likely to be damaged too (hence the metal-on-metal sound).
Do Pistons go bad?
A bad piston can have been damaged in a variety of ways, including: Burned piston: The top of the piston has a hole burned through its top, or it may look melted. It is usually caused by excessive heat in the cylinder. Cracked piston: The piston has cracks, going partially or completely through it.
Can I change crankshaft without removing the engine?
Although crankshafts are traditionally removed after the engine has been pulled from the engine bay, it is possible to remove the crankshaft without pulling the engine.
How do I know if I need new pistons?
According to many industry experts, if the pin bore is worn more than 0.002″, the piston should be replaced. Measure the piston at its gauge point with a micrometer to determine if it has worn significantly. In cases of extreme detonation or heat, the skirts could have collapsed which will show on the gauge.
What burns a hole in a piston?
Holes in pistons are caused by lean mixtures or severely advanced timing at high RPM. Since you can not change the timing and the knock sensor will retard it that leaves lean. Lean can be caused by the wrong injectors and/or low fuel pressure.
What does a bad piston sound like?
A hollow, muffled, almost bell-like sound is usually piston slap. This condition is caused by a piston rocking back and forth within its cylinder. A continuous piston slap sound is usually caused by worn pistons, excessive piston-to-wall clearance, misaligned connecting rods, worn cylinder walls, or inadequate oil.
How much does it cost to fix a piston slap?
This usually costs between $100 – $200 for most cars including labor. If you don’t see any damage, then what you need to do is readjust the tension of the belt.
How many hours do boat motors last?
The average marine gasoline engine runs for 1,500 hours before needing a major overhaul. The average marine diesel engine will run for more than three times that long and log an average 5,000 hours under the same conditions.
How much fuel does a 70 hp outboard use?
Rule of thumb – a motor will burn (in gallons) 10% of it’s horsepower at full throttle. As Joe points out, you can cut that number in half by finding your “cruise speed”. So if you have a “two speed motor – idle and full throttle” expect to burn upwards of 7 gallons per hour at wide open with a 70 horse model.
Are boat motors hard to work on?
But they are much easier to work on: A good boatyard can do a total outboard engine swap in a couple of hours, where the job for a diesel is measured in days. Space efficiency: Horsepower for horsepower, outboards are smaller than other marine power options.